Fitter Trade Operations - II

get iti website @ 1800/-

 

 

  • To hold the job in a four jaw chuck and do facing operation on both the ends using knife tool.
  • To measure the diameter using the steel rule and outside caliper.
  • To do facing, turning and chamfering operation on the job, holding it in a three jaw chuck.
  • To practice plain and taper turning, reducing and checking.
  • To practice single edge step turning.
  • To practice double edge step turning.
  • To practice turning and taper turning operation to make a 'B' slot and form the mandrel, and practice knurling operation.
  • To practice drilling, turning, boring and brush step boring on the job and recess cutting.
  • Cutting the’ V’-groove on the lathe machine using a taping die and matching the nuts and bolts.
  • Drilling through holes and filing the radius and the surface of the MS flat job with complete accuracy.
  • To file the radial and conical surfaces with an accuracy of ±0.05 mm and fitting the radial and conical Workpieces.
  • To practice double square and radius fitting.
  • To practice square fitting, drilling and tapping.
  • To practice straight fitting.
  • To practice the triangular fitting.
  • To practice radius and angular fitting.
  • To make bracket while doing marking, bending, filing, drilling, riveting and checking alignment using try square.
  • To practice drilling and tapping.
  • To practice the universal state of holes and checking it while marking, filing, drilling, taping, drawing and stud fitting.
  • To practice counter sinking, counter boring and reaming.
  • To practice filing and scraping on the bearing surface with accuracy.
  • To practice external and internal radial and angular fitting.
  • Prepare the ± 0.04 mm dovetail sliding using lower pin and screws.
  • To prepare parallel and angular matching, thread cutting and sliding fit by using die with precision of ± 0.04 mm.
  • To assemble the parts of a machine.
  • To repair the parts of the machine.
  • Setting up of the arc welding plant and practicing arc striking.
  • Welding the MS sheet using the filler rod or without using the filler rod as shown in the drawing.
  • Making a bid in a straight line from a 10 mm thick mild steel plate placed in a flat position as given in the drawing.
  • Making a square butt joint using the butt weld from the MS sheet in a flat state.
  • To make the fillet weld (external corner joint) with a 3.5 mm mild steel sheet in a flat state according to the given drawing.

Fitter Practical I, II Year

Submitted by iti on 9 August 2020 - 10:25am
Fitter Practical I, II Year

ITI Book Fitter Practical I, II Year is by Manish Sharma. Fitter Practical I, II Year is according to Latest NSQF Level. Fitter Practical I, II Year is according to latest syllabus of DGT(NCVT). Fitter Practical I, II Year is for I Year, II Year. Fitter Practical I, II Year is for ITI trade Fitter .

Fitter Trade Introduction Safety Precautions and First Aid
Fitter Skill Information - I
Fitter Trade Operations - I
Fitter Skill Information - II
Fitter Lathe Machine
Fitter Trade Operations - II
Fitter Trade Operations-III
Fitter Trade Operations - IV
Fitter Viva Practice
Read More : Fitter Practical I, II Year about Fitter Practical I, II Year
  • 46033 reads

ITI Student Resume Portal

रिज्यूम पोर्टल का मुख्य उद्देश्य योग्य छात्रों की जानकारी सार्वजनिक पटल पर लाने की है जिससे जिन्हें आवश्यकता हो वह अपने सुविधा अनुसार छात्रों का चयन कर सकते हैं

ITI Student Resume

Search engine adsence